. TABLE OF CONTENTS 01 1st Phone Number. 8 FEATURES 02 1st Account Code. 8 SPECIFICATIONS 03 2nd Phone Number.
9 04 2nd Account Code. 9 INSTALLATION 05 to 10 Reporting Codes. 9 Mounting the Panel. 3 05 Zone Alarm Reporting Codes.
- Entering [*][6][Master Code][8] with the system disarmed. The PC1550 can be programmed at the time of installation to automatically perform a test transmission to the monitoring station on a regular basis. If the system has not been programmed for this automatic lest, call the monitoring station for instructions on how to perform a test transmission.
- Home › Forums › DSC Technical Questions › Reprogram Master Code – DSC PC1550. Can anyone tell me how to reset it? BTW – the codes for the.
Nokia Security Master Code
Title: PC1500-PC1550 user Author: Ron Webb Subject: PC1500-PC1550 user guide Keywords: PC1500, PC1550, 1500, 1550, DSC Created Date: 11/7/1999 1:20:04 PM.
Features Specifications Keypad Programmable PC1550 Control Panel The PC1550 is complete with a default program so that it is. Six fully programmable zones operational with a minimum of programming. The control panel is - EOL resistor supervised option completely programmable from the keypad. Installation Mounting the Panel Fire Zone Wiring Select a dry location close to an unswitched AC source and close Any one of the 6 zones may be programmed as a Fire Loop. See to the telephone line connection. Remove the printed circuit board, Programming Guide section 11. Guidelines for Locating Smoke Detectors Experience has shown that all hostile fires in family living units generate smoke to a greater or lesser extent.
Experiments using typical fires in family living units indicate that detectable quantities of smoke precede detectable levels of heat in most cases. For these reasons, smoke detectors should be installed outside of each sleeping area and on each additional story of the family unit. The “Armed” light will flash to indicate that the The PC1500RK remote keypad provides complete information and system is armed without an entry delay. Control of the PC1550 control panel. The control panel can be fully Disarming programmed from the PC1500RK keypad.
The 6 zone lights provide Enter the premises through the designated entry-exit door. The Master Code may be changed here if the user has been enabled to change the Master Code, or in section 6. Loss of Time on System Clock When the PC1550 is powered 21 by the installer. 2 Set Auto-Arm Time entry delay.
This command allows the user to remain at home and The PC1550 can be programmed to arm at the same time each day. Have an instant alarm on the entry doors. At the selected Auto-Arm time, the bell will sound one short burst. Programming The essential information which defines the operation of the control function ON or OFF; the zone light will turn ON or OFF to indicate the panel is stored in a section of the EEPROM memory which is state of the function. All functions can be turned OFF at once by accessible using the Installer’s Programming code or via pressing 0. Where a zero is required in the account code, enter HEX ‘A’ (, 1,.
Dsc Pc1550 Master Code
Format Code 8, 9, A, B, C depending on ) to transmit 10 pulses which will be interpreted as a zero by the receiver type in section 23 monitoring station receiver. Transmission for operation of the F, A and P keys will only take 3 Interior Home-Away Loop operates the same as the type 2 place if the appropriate sections in 09 are programmed with a loop with the following exception. If the system is armed and the reporting code. Section 11, Digit #2 Summary: 14 3rd System Option Code 0 = Standard delay loop Use the same method of programming as section 12. 1 = Instant loop ZONE 2 = Interior Loop LIGHT 3 = Interior. Home / away loop ON = Access code required for bypass 4 = 24 hour. Zone 2 = 20.
Zone 6 = 60). The zero in the 2nd digit position each telephone number, enter one digit from the list below. See the tells the PC1550 not to send an extended round.
HEX data programming section for details on how to enter digits ‘A’. Openings “B” i.e. B2 = opening by user 2 This option configures the system for use with the LINKS1000. Closings “C” i.e. C4 = closing by user 4 Cellular Alarm Communicator. Refer to the LINKS Installation. Troubles “F” i.e.
See section 31, light 3. 34 6th System Option Code NOTE: Panels returned to DSC with the installer’s lockout feature enabled and no other apparent problems will be subject to an Use the same programming method as in Section 12. Additional service charge.